首頁制藥產品大全實驗室儀器及裝備實驗室常用設備罐體式脂質體擠出儀

罐體式脂質體擠出儀

更新時間：2024-10-22

價格：面議

品牌：暫無

型號：暫無

立即詢盤

產品詳情

是否為生產商：是

付款方式：預付

交貨周期： 30天內

主要銷售市場：亞洲

產品描述：

主要應用

◆阿霉素脂質體 Doxorubicin liposome

◆ 兩性霉素 B 脂質體 Amphotericin B liposome

◆ 紫杉醇脂質體 Paclitaxel liposomes

◆ 奧沙利鉑脂質體 Oxaliplatin liposomes

◆ 伊立替康脂質體 Irinotecan liposome

◆ SiRNA 脂質體 SiRNA liposome

◆ 白蛋白紫杉醇納米粒 Albumin paclitaxel nanoparticles

◆ 核酸類脂質體 Nucleic acid liposome

◆ mRNA脂質體 mRNA liposome

擠出原理

Extrusion Principle

樣品經過水化形成脂質體后，一般會通過高壓均質或者超聲的方式對樣品進行初步均質處理，處理后樣品粒徑和分布都會有所提高，但往往還不能達到所需要的理想要求。此時，將均質后樣品由下圖中進料口進入，通過高壓氮氣將樣品從濾膜中擠出，擠出后的樣品粒徑和分布都會進一步提高。

After the sample is hydrated to form liposomes, the sample is usually homogenized by high-pressure homogenization or ultrasonic wave. After treatment, the particle size and distribution of the sample will be improved, but it can not meet the desired requirements. At this time, the homogenized sample enters through the feed port in the figure below, and the sample is extruded from the filter membrane by high-pressure nitrogen. The particle size and distribution of the extruded sample will be further improved.

支撐板

Support plate

支撐板和濾板主要起到支撐濾膜的作用。由于磷脂有一定的相變溫度，所以在擠出之前需要對擠出器夾套通入恒溫水進行預熱至一定溫度（如70℃），且在使用過程中需保持在此溫度。通常的脂質體品種擠出之后粒徑能達到 100nm以下，PDI 能控制在 0.1 以下。

The supporting plate and filter plate mainly play the role of supporting the filter membrane. Since the phospholipid has a certain phase transition temperature, it is necessary to preheat the extruder jacket with constant temperature water before extrusion to a certain temperature (such as 70 ℃), which should be maintained in the process of use. After extrusion, the particle size of liposomes can reach below 100nm and PDI can be controlled below 0.1.

動力源：氮氣

Power source: nitrogen

技術特征

Technical features

◆核心部件 The core components

支撐板（SS316L不銹鋼）

Support plate (SS316L stainless steel)

濾板（SS316L不銹鋼）

Filter plate (SS316L stainless steel)

濾膜:PC材質（聚碳酸酯）

Filter membrane :PC material (polycarbonate)

密封系統：PU材質/聚四氟乙烯